Remedy:1 Check the M23 connector for proper connection and correct as necessary. The tray 3 upper limit sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started.Ĭauses:Tray 3 upper limit sensor (PS22) Tray 3 lift-up motor (M23) Paper feed/transport drive board (PFTDB) Printer control board (PRCB).– – 3 PS14 I/O check, sensor check PFTDB CN10-10 (ON) Q-4 4 M8 operation check PFTDB CN22-9 to 10 X-4 5 Change M8 – – 6 Change PFTDB – – 7 Change PRCBĭescription:Tray 3 feeder up/down abnormality – – 2 Check the connector of M8 for proper drive coupling and correct as necessary. Remedy:1 Check the M8 connector for proper connection and correct as necessary. The tray 2 upper limit sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started.Ĭauses:Tray 2 upper limit sensor (PS14) Tray 2 lift-up motor (M8) Paper feed/transport drive board (PFTDB) Printer control board (PRCB).– – 3 PS6 I/O check, sensor check PFTDB CN11-3 (ON) Q-1 4 M6 operation check PFTDB CN23-9 to 10 X-3 5 Change M6 – – 6 Change PFTDB – – 7 Change PRCBĭescription:Tray 2 feeder up/down abnormality – – 2 Check the connector of M6 for proper drive coupling and correct as necessary. Remedy:1 Check the M6 connector for proper connection and correct as necessary. The tray 1 upper limit sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started.Ĭauses:Tray 1 upper limit sensor (PS6) Tray 1 lift-up motor (M6) Paper feed/transport drive board (PFTDB) Printer control board (PRCB).The lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary.ĭescription:Tray 1 feeder up/down abnormality.– – 3 M25 operation check PFTDB CN13-6 (LOCK) X-11 4 Change M25 – – 5 PFTDB ICP6 conduction check – – 6 Change PFTDB – – 7 Change PRCBĭescription:Tray 3/4 feeder transportation motor turning at abnormal timing – – 2 Check the connector of M25 for proper drive coupling and correct as necessary. Remedy:1 Check the M25 connector for proper connection and correct as necessary. The lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary.Ĭauses:Transport motor (M25) Paper feed/transport drive board (PFTDB) Printer control board (PRCB).In memorial of Clark Middleton episode 6, season 8 of The Blacklist.ĭescription:Tray 3/4 feeder transportation motor failure to turn To enter (change) the password, select the check box, then enter a new password.Raymond ‘Red’ Reddington (James Spader) in front of a bizhub c452
#Bizhub c452 firmware password
: Enter the password of the user name you entered into (using up to 32 characters). : Enter the login name used for proxy authentication (using up to 32 characters). Select whether to use Proxy Authentication. If necessary, change the proxy server port number. Select to establish an external connection via a proxy server.Įxample of host name entry: ""Įxample of IP address (IPv4) entry: "192.168.1.1"Įxample of IP address (IPv6) entry: "fe80::220:6bff:fe10:2f16" In the administrator mode, select -, then configure the following settings.
#Bizhub c452 firmware update
To update the firmware manually, refer to Here.Ĭonfigure the setting to download firmware to this machine via HTTP. To update the firmware automatically by specifying the time, refer to Here.
#Bizhub c452 firmware how to
Configure the proxy server setting according to your operating environment.įor details on how to configure a setting for downloading firmware via FTP, refer to Here.įor details on how to configure a setting for downloading firmware via HTTP, refer to Here. You can download it either via FTP or HTTP. To use this function, the optional Hard Disk must be installed in this machine. For details, contact your service representative. The firmware and configuration information must be updated by your service representative. To externally download firmware and configuration information of this machine and update them, follow the procedure shown below. You can keep using the machine even while downloading firmware or configuration information. You can externally download firmware and configuration information of this machine to update them.